|
|
| (Eine dazwischenliegende Version desselben Benutzers wird nicht angezeigt) |
| Zeile 1: |
Zeile 1: |
| =Zugriff=
| |
| *Zugriff über Telnet auf Port 23
| |
| **telnet <IP oder FQDN>
| |
| =Konfigurations-Menü=
| |
| [[Datei:nortel-konfig-screen-1.png]]
| |
|
| |
|
| =Zugriff auf die Konsole=
| |
| [[Datei:nortel-konfig-screen-2.png]]
| |
|
| |
| =enable=
| |
| *5510-24T>enable
| |
| *5510-24T#
| |
|
| |
| =show-Befehle=
| |
| ==running-config==
| |
| *show running-config
| |
| <pre>
| |
| 5510-24T#show running-config
| |
| ! Embedded ASCII Configuration Generator Script
| |
| ! Model = Ethernet Routing Switch 5510-24T
| |
| ! Software version = v6.2.0.008
| |
| !
| |
| ! Displaying only parameters different to default
| |
| !================================================
| |
| enable
| |
| configure terminal
| |
| ...
| |
| ...
| |
| ...
| |
| </pre>
| |
| ==interfaces==
| |
| *show interfaces
| |
| <pre>
| |
| Status Auto Flow
| |
| Port Trunk Admin Oper Link LinkTrap Negotiation Speed Duplex Control
| |
| ---- ----- ------- ---- ---- -------- ----------- -------- ------ -------
| |
| 1 Enable Down Down Enabled Enabled
| |
| 2 Enable Down Down Enabled Enabled
| |
| 3 Enable Down Down Enabled Enabled
| |
| 4 Enable Down Down Enabled Enabled
| |
| 5 Enable Down Down Enabled Enabled
| |
| ...
| |
| ...
| |
| ...
| |
| </pre>
| |
|
| |
| ==vlan==
| |
| *show vlan
| |
| <pre>
| |
| Id Name Type Protocol PID Active IVL/SVL Mgmt
| |
| --- -------------------- -------- ---------------- -------- ------ ------- ----
| |
| 1 VLAN #1 Port None 0x0000 Yes IVL Yes
| |
| Port Members: 1-6
| |
| 2 VLAN #2 Port None 0x0000 Yes IVL No
| |
| Port Members: 7-12
| |
| </pre>
| |
|
| |
| ==ip route==
| |
| *show ip route
| |
| <pre>
| |
| ===============================================================================
| |
| Ip Route
| |
| ===============================================================================
| |
| DST MASK NEXT COST VLAN PORT PROT TYPE PRF
| |
| -------------------------------------------------------------------------------
| |
| Total Routes: 0
| |
| -------------------------------------------------------------------------------
| |
| TYPE Legend:
| |
| I=Indirect Route, D=Direct Route, A=Alternative Route, B=Best Route, E=Ecmp Rou
| |
| te, U=Unresolved Route, N=Not in HW
| |
| </pre>
| |
|
| |
| =Konfigurieren=
| |
| *5510-24T#configure terminal
| |
| Enter configuration commands, one per line. End with CNTL/Z.
| |
| 5510-24T(config)#
| |
|
| |
| ==Allgemeine Konfiguration (IP, Netmask, Gateway)==
| |
| *ip address switch x.x.x.x netmask y.y.y.y default-gateway z.z.z.z
| |
|
| |
| ==Hostname==
| |
| <pre>
| |
| 5510-24T(config)#snmp-server name 5510-24G
| |
| 5510-24G(config)#snmp-server name 5510-24T
| |
| 5510-24T(config)#
| |
| </pre>
| |
|
| |
| ==Authentication local==
| |
| *per Default heißen die Usernamen für den Login "RO" für die "Read-Only"-Ebene und "RW" für die "Read/Write"-Ebene
| |
| *Um das zu ändern den folgenden Befehl eingeben:
| |
| **username <username> <new password> ro/rw
| |
|
| |
| alternativ:
| |
| *cli password read-write/read-only <password>
| |
|
| |
| ===Passwort-Abfrage aktivieren===
| |
| *cli password telnet local
| |
|
| |
| ===Passwort-Abfrage deaktivieren===
| |
| *cli password telnet none
| |
|
| |
| ==Authentication Serial-Port==
| |
| ===Passwort-Abfrage aktivieren===
| |
| *cli password serial local
| |
|
| |
| ===Passwort-Abfrage deaktivieren===
| |
| *cli password serial none
| |
|
| |
| =VLAN=
| |
| ==ip routing aktivieren==
| |
| *ip routing
| |
| ==Create VLAN==
| |
| *vlan create <Nummer> name "<Name>" type port
| |
| ==Configure VLAN==
| |
| *interface vlan <Nummer>
| |
| *ip address 0.0.0.0 255.255.255.255
| |
| *exit
| |
| ==VLAN einem oder mehreren Ports zuweißen==
| |
| *vlan members add <vlan-nummer> <Portnummer>
| |
|
| |
| =DHCP-Relay=
| |
| *Zunächst einen DHCP-Server einrichten
| |
| ==dhcp-relay aktivieren==
| |
| *5510-24T# configure terminal
| |
| *5510-24T(config)# interface vlan 55
| |
| *5510-24T(config-if)# ip dhcp-relay
| |
|
| |
| ==dhcp-server eintragen==
| |
| *5510-24T(config)# ip dhcp-relay fwd-path <IP-Vlan> <IP-DHCP-Server> enable
| |
|
| |
| =SNMP=
| |
| ==SNMP-Community benennen und SNMP aktivieren==
| |
| für read-only Ebene:
| |
| *snmp-server community <community-name> ro
| |
| für read-write Ebene:
| |
| *snmp-server community <community-name> rw
| |